Amer Networks SS3GR26i Guide d'installation

i SS3GR50i / SS3GR26i L3 Gigabit Ethernet Switch With IP Stacking Installation Guide (v1.3)

Figure 1-4 SS3GR50I DC Power Input Pin-outs Distribution DC power has 3 pin-outs: PIN1: V+ DC power positive electrode input PIN2: V-

Indicator Off XFP transceiver is not connected. Transfer Indicator Act Blink (Green) Sending or receiving data Table 1.2 SS3GR50i/26i LEDs LED P

1.3.5 Front Panel Port Description SS3GR50i/26i switch support the following SFP transceivers: z MGBM-GSX Gigabit SFP MM 850nm, 500m (SX) z

Chapter 2 Hardware Installation 2.1 Installation Notice To ensure the proper operation of SS3GR50i/26i switch and your physical security, please read

Gas Average (mg/m³) Max (mg/m³) SO20.2 1.5 H2S 0.006 0.03 NO20.04 0.15 NH30.05 0.15 Cl20.01 0.3 Table 2.2 Environmental Requirements: Particles 2.1

of the power supply system. The input source for the switch should be reliable and secure, a voltage adaptor can be used if necessary. The building’s

 When mounting devices in an open rack, care should be taken to prevent the rack frame from obstructing the switch ventilation openings. Be sure to

Please unpack the shipping package and verify carefully the contents inside. SS3GR50i/26i switch should include the followings: ITEM No. Part name

Figure 2-1 Rack-mounting SS3GR50I Caution The brackets are used to fix the switch on the rack. They can’t serve as a bearing. Please place a rack

2.3.3 SFP Transceiver Installation An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-LH) can be used for a backbone connectio

ii Copyright © Amer.com Corp., 1997-2007 All rights reserved. No part of this publication may be reproduced in any form or by any means or used to ma

The switch has 2 10Gb fiber transceiver slots. The procedure for installing the XFP 10Gb fiber transceiver is shown below: Step 1: Put on an ESD

2.3.6 Connecting Switches in a Stack Figure 2-4 shows how the stack cables are connected between switches in a stack. Each stacking connection is a 4

3. Repeat steps 1 and 2 for each unit in the stack. Form a simple chain starting at the Down port on the top unit and ending at the Up port on the bo

1. Insert one end of the power cable provided in the accessory kit into the power source socket (with overload and leakage protection), and the other

iii Overview SS3GR50i/26i switch is a high performance route switch, that can be deployed as aggregation equipment for IP metropolitan area networks

iv FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rul

Table of Contents Overview...iii

Chapter 1 Introduction 1.1 Product Brief SS3GR50i/26i front panel: Figure 1-1 SS3GR50i and SS3GR26i Switch 1.1.1 Overview SS3GR50i/26i switch s

into separate broadcast domains with IEEE 802.1Q compliant VLANs, empowers multimedia applications with multicast switching and CoS services, and eli

port level security and block illegal users.  QoS SS3GR50i/26i switch switch fully support DiffServ Module. Users can specify a queue bandwidth

SS3GR50i: 6.1 kg SS3GR26i: 5.7 kg  Mean Time Between Failure Min. 80, 000 Hours MTBF 1.3 Description of Hardware 1.3.1 Front Panel The fron